To install the cover, press lower edge until clips are secured to hose. Start all 4 screws until stepped flange engages the fender but do not fully tighten. Remove screw from center of belly pan A 6mm internal hex. On the other part of the disconnected regulator plug. Be sure pad is secured in place and not damaged or torn. For chrome surfaces, use either a window-cleaning solution or a polish specifically designed for chrome.
Remove 5 console screws using a 4 or 6mm hexagonal wrench. Pull rear head pipe rearward and rotate it outward until clear of the engine and front head pipe. Slide the control forward or rearward in its track until the threaded hole of the control aligns with the front 2 or rear 3 screw hole in the footrest support. Be sure peg at bottom of panel is aligned with hole in each lower access panel. Torque spark plugs to specification. Pull straight outward at the rear of the access panel to disengage the rear-most tab A and hold it clear of the peg on the tail trim panel. If normal washing does not remove these materials, you may need to use a special cleaner.
Engine and exhaust components get hot and remain hot for a period of time after the engine is stopped. A motorcycle starter relay is an electronic mechanical switch that has a small coil winding around a piece of metal that requires low amperage and thin wires to be activated. Tip the front battery box with battery toward battery box and install bolt 3. Remove these from one bag only. If steering binds, feels rough or uneven, or if movement is detected at steering stem, adjust or replace steering head bearings as necessary.
Move the muffler back and forth to expand the joint and allow lubricant to enter the joint. Secure pump body in a soft jaw vise. Turn the throttle closing cable rear cable adjuster out just until slight resistance is felt. Pull hose out from behind left leg fairing. Use the troubleshooting charts contained in this chapter before removing and disassembling the engine. Torque four outer screws to 9. It is recommended to have the engine running whenever using the audio system.
Press + or - on the passenger control to raise or lower the rear headset volume. Prepare fuel tank for assembly by thoroughly cleaning inside the tank and all sealing surfaces, including the opening for the pump. When a disc is found, the disc number A , track number B , and track time duration C will be shown on the console display screen. Just want spark or aeon will be soaked in gas and lit. Connecting the negative cable first increases the risk of sparks and an electric shock that could result in damage or injury. Carefully remove the pump from the tank by lifting and turning the assembly 180 degrees, then tilt the assembly forward and complete pump removal. Install all fasteners lightly and fully seat the spring clips before fully tightening any screws.
The aeon lost spark figure they have same wire harness. Remove upper fender screws B. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. Grasp the rear wheel and push firmly side-to-side B. Antidote: External: Flush with water. If the key and the identification number are lost or misplaced, the lock set must be replaced.
You should read something around 0. Replace drive belt and both sprockets as a set if the drive system has over 5,000 miles 8,000 km of service at the time of damage or failure. Good luck and have a wonderful day. Disconnect overflow drain hose from the fuel cap basin. While warming up, check for oil leaks. Engine exhaust from this product contains poisonous carbon monoxide gas that can cause loss of consciousness and may lead to death.
Remove lower access panels page 3. Remove three screws along the rear edge of inner saddlebag that fasten the bag to the tail light housing. The headlamp, taillight, running lights, radio, and instrument lights illuminate. Broken wire or worn insulation exposing wire to a ground situation especially inside wire harness at tight bends around fairing brackets, under dash panels, under fuel tanks over cylinder heads, etc. Initially, the standard models of the company was selected the classic bike 50s. Clean oil line sealing surfaces on engine. Clean and dry the sealing surfaces of the reservoir, reservoir cover, diaphragm, and diaphragm plate with a clean lint-free cloth.
Simple ground wire a mouse I think chewed but. Install the plug and place the hose behind the left leg fairing. Be careful to avoid grinding wheel contact with the finished area of the stand. Install the desired input cable. If level is low, check brake pads for wear page 2.